DIY Coffee Table Tic Tac Toe Board

Ready to make something for your home? Yes? Good. A couple weeks ago, I mentioned that we went Geocaching in this post. While we were driving through the desert near our house, we spotted a pile of discarded slate tiles. (Yeah, people dump their junk in the desert sometimes. Beyond aggravating.) So we stopped, I sifted through them, and brought several of them home for a project - A Tic Tac Toe Board to be exact. Not just any old Tic Tac Toe board, but a Coffee Table Tic Tac Toe Board. So much fun, right? Why didn't we think to do this sooner??

Here's what you need:
- 9 slate tiles 3 1/2 x 3 1/2 inches
- 11 1/2 x 11 1/2 x 1 1/2 board  (we used a 2x12x8 ft board. planks are always 1/2 inch smaller than advertised)
- liquid nails (we used Loctite Pro Line)
- dark walnut wood stain
- sand paper
- 1 sheet of adhesive vinyl
- white acrylic paint
- craft sponge brush
- this Silhouette file (optional)

Here's how to make this Tic Tac Toe Board:

Use the sandpaper to smooth down all the corners, and any rough spots.

Seal the wood using the wood stain. Be sure to follow the directions on the wood stain and allow for the proper drying time.

Use the Silhoutte to cut out this file onto adhesive vinyl to create a stencil. (If you don't have a Silhoutte, then skip this step or decorate the sides in your own way.)

Place each stencil on the sides of the board. Paint each side using the craft sponge brush. Gently peel the stencil off the wood.

Once the paint has dried, arrange the tiles until you are satisfied. Glue one tile on at a time, making sure to place each tile in the exact position as previously arranged. Allow to dry over night before use.

That's it. It's definitely not a difficult project, but you do you have to allow drying time...always a little challenging for us impatient people! ;) Totally worth the wait, though.

Enjoy!

Hooded Denim Jacket DIY

My husband has nicknamed me the "Lazy Seamstress." Maybe I should be horrified, but when he first called me that, it made me laugh for about 2 minutes straight. Why? Because it's true. So. Terribly. True. I'm not in love with sewing or anything, but it's definitely a very necessary means to an end. I tend to avoid any sewing projects that do not involve sewing in a straight line. Why am I telling you this? I'm telling you this because I made something amazing. Something that I've had on my list of Things to Make for years. It sat on my list for years, because I wasn't sure how I was going to make it. I just knew I wanted a hooded denim vest jacket. I found plenty of tutorials, but none of them were quite what I was looking for - an easy, minimal-sewing tutorial that didn't involve taking apart the jacket. All I wanted to do was cut off the denim sleeves leaving vest portion, insert a zip-up hoodie, and then find a way to attach them. In my head it seemed easy enough, but I just couldn't figure out how to make this without over-complicating it (I'm really good at this) until I talked it over with my mom, Aka Seamstress Ninja. Guess what? It was waaay easier than I realized! Major win for the Lazy Seamstress! ;)

Supplies needed:
- zip-up hoodie
- denim jacket
- basic sewing supplies (sewing machine, scissors, thread, and pins)

Let me first give you one quick note about matching a denim jacket with a hoodie. For the best rest results, it's important to find a hoodie and denim jacket that are close in size as well as the same sized sleeve openings, near the armpit, since you have to slip the hoodie into the arm hole openings of the denim jacket. Also, make sure both the denim jacket and the hoodie are freshly washed and wrinkle free. Got it? Good.

Start out by cutting off the sleeves of the denim jacket below the seam that attaches the sleeves to the vest. Trim as close to the seams as desired, but be sure to leave the arm hole seam intact.

The hoodie that I used in this project had a bunch of stuff sewn onto the front. I felt like most of it detracted from the jacket as a whole, so I ripped out the letter seams and removed the letters from the front.

Line up the seams as best as possible

Next, insert the hoodie inside the denim vest. For best results, work on a flat surface. Button each button and zip up the hoodie. Smooth out all the wrinkles and folds and line up the side and shoulder seams of the hoodie with the seams of the vest as close as possible.

Carefully, pin the hoodie to the vest at both arm openings. This portion is not hard, but takes a little patience. Be sure that the seams from the vest and hoodie line up as closely as possible while pinning. This is truly the most important step of this project.

Once the pins have been placed on both the left and right sides of the sleeve openings, sew the vest and jacket together at the sleeve openings along the seam of the denim jacket or in between the two seams of the arm holes. I began sewing at the armpit of the vest on the backside and worked my way over the backside towards the front. Repeat the same process on the opposite arm hole.

Additional seam sewn across back for added security

Once both arm holes have be sewn, lay the hoodie/vest on a flat surface again, front facing down. Pin the backside of the vest to the hoodie along the back seam that runs across the shoulder blades. Run the pinned portion through the sewing machine for a little added security, to keep both layers together.

BAM! That's it! After I finished, I just sat there, amazed and speechless over how easy and awesome this jacket turned out. I didn't even mess up!!! (I usually end up ripping out a couple of seams on each sewing project). Ha!

Love it? Guess what? Just when you thought this project couldn't get any cooler, it does. I have one more amazing upgrade for this jacket. Click here to see how I stenciled the back. I promise you won't be disappointed :)

How to Make an Infinity Scarf

Have you ever seen The Sound of Music? Remember the part when Maria von Trapp sewed play clothes for the children out of the drapes?  The idea of turning window dressings into clothes, has always amused me. One day, while rummaging through some fabric scraps, I found a forgotten set of curtains that were given to me several years ago. The problem was that they didn't match anything, so I never hung them up. So guess what I did with them? Did you guess, "Make play clothes for your children?"  Ha! Fooled you! Well, I didn't make clothes play clothes for my boys out of drapes (that would be weird), but I did upcycle an infinity scarf from a curtain.

After I came up with this idea, I planned out each step in my head and then proceeded with the project. Little did I know that my plan was unbelievably flawed! Really and truly this shouldn't have been a difficult project, but somehow I managed to over-complicate this project by leaps and bounds. So, after ripping out the seam (probably about 10 times), several phone calls and Skype sessions with my mom (I had to ask her for help. She's like the Sewing Master), I finally figured out how to make an infinity scarf. Now, I have good news for you - it's not hard, but I had to make 934,283 mistakes before I realized this. So, now that I know the right way as well as the easy way to make this, I'll show you how to make an infinity scarf.

You will need:
- fabric (mine was 24 inches x 70 inches)
- sewing machine
- matching thread
- scissors

If you plan to use a curtain like I did, make sure to remove the back panel of the curtain.

Fold the fabric in half lengthwise (the longer side) so that the backside of the fabric faces outwards. Pin and sew the long sides closed using a straight stitch to create a long "tube". Pull the fabric tube right-side-out.

Bring the two un-sewn ends together, making sure that the seam from both ends line up. Fold approximately 2 inches of the edge of Side B inside the tube. (tip - I had to iron the fold to keep the fabric in place). Slip the end of Side A (unfolded) into Side B and pin together, leaving an opening of approximately 5 inches (or more, if needed.)

Sew the ends together as far as possible. You won't be able to connect the entire circle using a sewing machine. Hand stitch the remainder to close the opening.

That's it friends! Now, go and make one!

How To Make a Lightning Bolt Shirt with Transfer Paper

Greetings, my crafty-loving friends! Want to make something for your kids today? Quick and easy? How about a shirt with an iron-on design? Yes? Ok, good. I'm glad you said, yes, because I really wanted to show you what I made for my preschooler. A couple of months ago, I was watching the movie Meet The Robinsons with Mac. Have you guys seen that movie? Love that movie. While we were watching it, Mac noticed Wilbur Robinson's lightning bolt T-shirt (the son of Lewis) and asked me to make a shirt like that for him. Well, of course I had to oblige!

Wilbur has the black shirt on

source

You will need:

- Ink Jet Hand Iron Transfer Paper for Dark Fabrics

- black t-shirt (Hobby Lobby sells them for about $3)

- iron

- ink jet printer (not a laser printer)

- this lightning bolt PDF

Before we begin, there's a couple of things I need to let you know about making the lightning bolt shirt. First of all, make sure to use transfer paper for dark fabrics, if you plan to iron the image onto a dark shirt. The image will not show up correctly if regular transfer paper is used. Got it? Ok, good. Next thing - this project can only be done with an ink jet printer. For real. So, if you have a laser printer, like we do, I recommend finding a friend with an ink jet printer and using theirs to print the image onto the transfer paper. Ink Jet transfer paper will not work with a laser printer. It will melt inside. So don't do it! Laser printer transfer paper is available on Amazon, BUT in order to get the image to adhere onto fabric, a super fancy and expensive ($200) heat press machine is needed. Irons will not work. Frustrating, I know. Because of this, I recommend finding a friend with an ink jet printer, like I did. (I have nice friends.)

Due to copyright issues, I chose to vary the lightning bolt slightly from Wilbur's shirt

To make this fun shirt, print the Lightning Bolt PDF onto a sheet of transfer paper, cut out the image, and iron it onto a clean (duh), pre-washed t-shirt. Be sure to read and follow the ironing instructions from the transfer paper package closely. Usually, the shirt needs to be washed and dried again after adhering the image onto the shirt before wearing, but you need to wait 24 hours after transferring the image before washing it. Crazy, right? Anyway, following the instructions for image transferring is important, but the results are well worth the small amount of effort it takes. 

And now, my friends, you have a super awesome shirt for your kids. This usually results in feelings of shock and awe from the children after they have realized that you have made this for them....all by yourself...well, maybe...

Ha ha!

How to Make a Beanie from a Sweater Sleeve

Have you had your fill of winter yet? Has Snowmageddon depleted your creative energy? Well, guess what? Here's an unexpected and easy sewing project to make for your little ones in one evening. This easy little project may just make these last days of winter a little more bearable, once you see your little ones wearing these cute little beanies on their heads.

These beanies were made with the leftover material from an upcycled sweater project that I shared a couple of weeks ago. The sweater originally had gigantic baggy sleeves that proclaimed, "I'm so outdated!" They just had to go. So, I cut them off and made a cute pair of boot cuffs, and still had a bit of leftover sleeve material. Instead of tossing them, I thought, "Why not make hats for the boys?"

Here's the original sweater. It's a hand-knit wool sweater and a bit on the heavy side. This project is totally doable with the heavy wool sweater, but would probably work out even better on a medium-weight sweater. You'll need need at least 12 inches of a sleeve to work with (per hat).

Here's how I made these cute little beanies:

Start out by serging each trimmed end of the sleeve to prevent the sweater from unraveling as you work on it.

Turn the sleeve inside out, fold one end, and pin it. (This is the top portion of the hat. So, if the sleeve has a smaller end, it would be ideal to use the smaller end here.) Side note: the photo shows both ends pinned, but you can pin each end and work on them one at a time.

Sew a line about 1 inch above the fold of the sleeve, leaving a 1 inch opening between the starting and ending points. Be sure to run the sewing machine forward and backward a couple of times to prevent the stitch from unraveling (at the starting and ending points), especially since the ends are not connected. (I used a serged stitch here, but a straight stitch would be fine too.)

While the sleeve is still inside out, fold the opposite end of the sleeve over, pin, and sew two separate lines over the folded portion.  Make one about 1/4 inch above the fold and one about 1 inch above the fold to create a faux brim. This time, make sure to connect the beginning and ending points.

Guess what? That's all the sewing needed! For. Real. Gasp!

Set aside the sleeve/hat. Braid three strands of yarn into approximately the length of 2 feet.

Tie one end of the braided yarn onto a small crochet needle.  Thread the yarn through the top opening of the hat (the end with the 1 inch opening) and out the other end to create a "drawstring".

Pull the yarn tight and tie square knot. Turn the hat right side out and pull drawstrings through the small opening at the top of the hat.

Trim the ends of the drawstrings, leaving approximately 8 inches (or more if you like), and tie off the ends. Make two pom poms and attach them to each end of the drawstring.

Double threaded a plastic needle with yarn, then "embroider" a cute pattern onto the "brim" of the hat.

Wa-La! That's it! Easy-Peasy. Who would have ever thought to make a hat out of a sweater sleeve??
:)